подходяща машина - предложения IDM Idimatic/66 Кантослепваща машина

Surplex - толкова е лесно да наддаваш!
Регистрация
Избери търг
Предложи
Открийте повече
Три начина за успешна продажба!
Покупка
Търг
Маркетинг
Открийте повече

IDM Idimatic/66 Кантослепваща машина

Този артикул е във Вашия списък за наблюдение
IDM Idimatic/66 kantoslepvascha mashina
IDM IDIMATIC/66 КАНТОСЛЕПВАЩА МАШИНА
ПРОДАДЕНО
   

Съжаляваме, но тази машина е вече продадена

Намери подобни налични машини

Разходи и услуги

Такса за търга   15%
ДДС   *плюс ДДС
Условия за доставка   натоварен на камион
Цени за демонтаж и товарене   400.00 € (обвързващи)
Разходи по транспорта   не са включени
Условия на плащане   100% плащане преди вземане

Детайли за машината

Име   IDM Idimatic/66 Кантослепваща машина
Машина №   185033
Производител   IDM
Модел / Вид   Idimatic/66
Дата на производство   1995
Машината е достъпна от   11.17.2014
Качество на машината   в изправност
Местоположение на машината   33070 BUDOIA (PN), Italien

Технически детайли

дебелина на ръба   0,4 - 5 mm
дебелина на обработваното изделие   10 - 50 mm
мин. ширина на обработваното изделие   140 mm
устройство за обрязване на свръзки   2 x 2,2 kW
устройство за рязане   2 x 0,35 kW
Приблизителни размери   7500 x 1400 x 2400 mm
Приблизително тегло   3800 kg

Описание

•Edgebanding thickness capacity, 10 – 50 mm panel thickness, 60 mm minimum panel width & 140 mm minimum length

•Pre-milling station with (2) 3 HP – 12,000 RPM counter rotating vertical milling heads: both with pneumatic jump control, 30 mm spindles, fully enclosed by noise insulated cabin

•Gluing unit for edges up to 3 mm thickness, 56 mm height.

•Front & rear end trims (motors 0.5 HP – 12,000 RPM each), motors tilt 0° - 15° on horizontal plane, 45° chamfer cut with on/off on control.

•Top & bottom rough trims (motors 0,7 HP – 12,000 RPM each), (prepared for “quick change” of motors, for interchangeable 2nd set of bevel/radius trim units)

•Top & bottom fine/bevel/profile multi-function trims (motors 0.6 HP – 12,000 RPM each), tilts 0°- 10° for bevel and 3 mm PVC corner round (prepared for “quick change” of motors, for interchangeable 2nd set of bevel/radius trim units)

•Moulding unit (motor 2,5 HP – 12,000 RPM each), units tilt 0° - 90°.

•Corner rounding units from trimming leading & trailing upper and lower edge/corners when edgebanding all (4) sides or when edgebanding “soft- or postformed” panels (4 motors 0.7 HP – 12,000 RPM each).

•Top & bottom scrapers for up to 5MM thick PVC banding, pneumatic pressure control for scraping knives, digital readouts, overhead PVC filter unit eliminates PVC chips being sucked in by dust collector.

•Top & bottom PVC edge color & surface reactivation unit, LEISTER hot air blower with temperature adjustment

•Function & line control with microprocessor

•Microprocessor displays stored data, on/off workstation sequence & trouble shooting diagnostic; data input by alphanumeric keyboard; microprocessor adjusts according to stored programs or input; top pressure beam opening, pressure section position & pressure control, in/out pneumatic sideways positioning of “trim/scrap/corner round” workstations, on/off sequence of workstation motors

•Equipped with automatic strip & coil feed magazine with 3 mm PVC guillotine

•0.7 Kg capacity overhead granular glue “Quick Melt” hopper feeding compact size, Teflon coated lower applicator glue pot, 25 mm diameter glue applicator roller, reversible rotation by flip of switch

•Pressure section with (1) large diameter (200 mm) clutch controlled drive roller and (4) jump action, pneumatic pressure idle rollers, horizontal Adjustment w/digital indicator

•Hardened steel link feed chain with “anti-slip” 80 mm wide rubber pads

•(2) feed speeds, with 2.2 Kw or 3.3 Kw drive

•Motorized adjustment of top pressure beam. Heated infeed fence, automatic panel spacing control, remote control job button, insulated sound enclosure over all trim stations; rotating operator control panel at eye-level height, 15 KVA – 240 Hz frequency inverter & complete set of used tooling

Machine specifications are based on original manufacturer’s information as reported in the original manual of this machine and are subject to verification.
Отиди горе