kone-ehdotukset IDM Idimatic/66 Reunalistakone

HOMAG Optimat KL 77/A20/S2 Reunalistakone
0 Gebote
6,500 €
15.12.2016
10:00
OTT Altantic Edge Banding Machine
0 Gebote
5,500 €
15.12.2016
12:26
BRANDT KD 68 Reunalistakone
11 Gebote
950 €
15.12.2016
10:25
HEBROCK EURO 2000 Reunalistakone
1 Gebote
1,000 €
15.12.2016
10:36
Surplex - niin helppoa tarjota!
Rekisteröidy
Valitse huutokauppa
Tarjous
Lisätietoja
Kolme tapaa onnistuneeseen kauppaan!
Osto
Huutokauppa
Markkinointi
Lisätietoja

IDM Idimatic/66 Reunalistakone

Tämä artikkeli on sinun katsottavien lista

Valitamme, tämä kone on jo myyty

Löydä samanlaisia saatavilla olevia koneita

Kustannukset ja hyödyt

huutokauppamaksu   15%
ALV   *sekä ALV
Kuljetusehdot  
Purku- ja lastausmaksut   400.00 € (binding)
Kuljetuskustannukset   ei sisälly
Maksuehdot  

Koneen yksityiskohdat

Nimi   IDM Idimatic/66 Reunalistakone
Kone nro   185033
Valmistaja   IDM
Malli / tyyppi   Idimatic/66
Valmistusvuosi   1995
Kone saatavilla alkaen   11.17.2014
Koneen laatu   toimiva
Koneen sijainti   33070 BUDOIA (PN), Italien

Tekniset tiedot

reunan paksuus   0,4 - 5 mm
työkappaleen paksuus   10 - 50 mm
työkappaleen minimileveys   140 mm
liitoksen viimeistely-yksikkö   2 x 2,2 kW
leikkausyksikkö   2 x 0,35 kW
Mitat noin   7500 x 1400 x 2400 mm
Paino noin   3800 kg

Kuvaus

•Edgebanding thickness capacity, 10 – 50 mm panel thickness, 60 mm minimum panel width & 140 mm minimum length

•Pre-milling station with (2) 3 HP – 12,000 RPM counter rotating vertical milling heads: both with pneumatic jump control, 30 mm spindles, fully enclosed by noise insulated cabin

•Gluing unit for edges up to 3 mm thickness, 56 mm height.

•Front & rear end trims (motors 0.5 HP – 12,000 RPM each), motors tilt 0° - 15° on horizontal plane, 45° chamfer cut with on/off on control.

•Top & bottom rough trims (motors 0,7 HP – 12,000 RPM each), (prepared for “quick change” of motors, for interchangeable 2nd set of bevel/radius trim units)

•Top & bottom fine/bevel/profile multi-function trims (motors 0.6 HP – 12,000 RPM each), tilts 0°- 10° for bevel and 3 mm PVC corner round (prepared for “quick change” of motors, for interchangeable 2nd set of bevel/radius trim units)

•Moulding unit (motor 2,5 HP – 12,000 RPM each), units tilt 0° - 90°.

•Corner rounding units from trimming leading & trailing upper and lower edge/corners when edgebanding all (4) sides or when edgebanding “soft- or postformed” panels (4 motors 0.7 HP – 12,000 RPM each).

•Top & bottom scrapers for up to 5MM thick PVC banding, pneumatic pressure control for scraping knives, digital readouts, overhead PVC filter unit eliminates PVC chips being sucked in by dust collector.

•Top & bottom PVC edge color & surface reactivation unit, LEISTER hot air blower with temperature adjustment

•Function & line control with microprocessor

•Microprocessor displays stored data, on/off workstation sequence & trouble shooting diagnostic; data input by alphanumeric keyboard; microprocessor adjusts according to stored programs or input; top pressure beam opening, pressure section position & pressure control, in/out pneumatic sideways positioning of “trim/scrap/corner round” workstations, on/off sequence of workstation motors

•Equipped with automatic strip & coil feed magazine with 3 mm PVC guillotine

•0.7 Kg capacity overhead granular glue “Quick Melt” hopper feeding compact size, Teflon coated lower applicator glue pot, 25 mm diameter glue applicator roller, reversible rotation by flip of switch

•Pressure section with (1) large diameter (200 mm) clutch controlled drive roller and (4) jump action, pneumatic pressure idle rollers, horizontal Adjustment w/digital indicator

•Hardened steel link feed chain with “anti-slip” 80 mm wide rubber pads

•(2) feed speeds, with 2.2 Kw or 3.3 Kw drive

•Motorized adjustment of top pressure beam. Heated infeed fence, automatic panel spacing control, remote control job button, insulated sound enclosure over all trim stations; rotating operator control panel at eye-level height, 15 KVA – 240 Hz frequency inverter & complete set of used tooling

Machine specifications are based on original manufacturer’s information as reported in the original manual of this machine and are subject to verification.
Ylös