Surplex használt gépek
Vétel Surplex Trust
Smooth auction process - Surplex informs you about the current situation: more information

Aukció 'KUPER Stock Machines (Part 3)': sorszám 67 HOMAG KL 77/A20/S2 Élzárógép
Németország, 33397 Rietberg

Lezárási időpont
ekkor: 10 nap 18 óra
2020.07.21, 11:29
Jelenlegi legmagasabb licit
2,450
1 licit, 14 figyeli
Kérem,jelentkezzen be
2,650
következő lehetséges licit
Licitáljon most

Részletek

Árkalkulátor
Nyomtatás
Van bármilyen kérdése vonatkozásában a gép? Kérjük, lépjen kapcsolatba velünk.
Név: HOMAG KL 77/A20/S2 Élzárógép
Termékszám: 563401
Gyártó: HOMAG
Típus: KL 77/A20/S2
Gyártás éve: 1998
Ekkortól elérhető: immediately
Gép minősége:
Helyszín: Németország, 33397 Rietberg
HOMAG - EDGES - OPTIMUM
One-sided machine for gluing and finishing
of different edge materials from the roll
or as strips, up to 20 mm edge thickness, on straight
tear-free workpiece edges in longitudinal and transverse throughput.

Fixed stop side on the left.

BASIC MACHINE:
- with continuous machine column for
  flexible structure of the processing units
- Workpiece support with roller rail,
  telescopic approx. 800 mm
- Chip channel in the machine base
- Glue roller drive with feed stop
- Glue container lift-off at feed stop
- Glue container clamping workpiece-actuated
- Adjustable infeed ruler

WORKPIECE TRANSPORT DEVICE:
- transport chain 80 mm wide with rubber pad
- hardened precision running and guide surfaces
- magnetic braking of the transport chain

SURFACE:
- with driven compound V-belt
- motor-driven height adjustable with digital
  Position display

PAINTING:
- HOMAG - textured paint grey RDS 240 80 05

ELECTRICAL EQUIPMENT:
- Operating voltage 380/400 volts, 50/60 Hz.
- Country specific operating voltage adjustment
  via transformer (optional at extra cost)
- Control voltage 24 Volt
- Switch cabinet mounted, according to Euronorm
  EN 60204 installed
- electronic frequency converter with
  Motor brake function
- Manual switch for setup operation

HOMATIC - ELECTRONIC CONTROL:
- Programmable logic controller (SPS)
  with LED display of all in- and
  Outputs
- Integrated draw frame control for contact
  Loose control of the processing aggregates
- Prescribed by-pass temperature:
  +5 degrees to +35 degrees Cels.

CONTROL NC21
HOMATIC control system with graphical user interface
for simple and convenient operation and programming
a HOMAG machine

Hardware:
- Industrial computer 68040 with 16 MByte RAM
- 1 PCMCIA - hard disk 170 MByte
- 1 free PCMCIA slot for data backup
- Colour display 10.4" with PC-compatible keyboard
  installed in the control panel at the inlet
- expandable with network connection Ethernet

software:
- Real-time operating system OS9 with Windows interface
- Operation with Windows standard via selection menu
- menu-driven creation of work programs
- Production according to work programmes
- SPS diagnosis in ladder diagram technology on the display

SAFETY AND PROTECTIVE EQUIPMENT:
- all machines for EU member states with
  CE mark according to EC Machinery Directive
  89/392/EEC Annex II A
- Wood dust tested TRK value max. 2 mg/m3 at
  Compliance with the requirements to be provided by the customer
  Extraction capacity according to extraction plan
- Documentation

TECHNICAL DATA:
- Feed rate infinitely variable 18 - 24 m/min
- Working height 950 mm
- Working width minimum:
           - 55 mm with workpiece thickness 22 mm
           - 100 mm for workpiece thickness 60 mm
  (depending on the workpiece length)
- workpiece overhang 30 mm
- workpiece thickness 12 - 60 mm
- Edge material strips max. 0.4 - 20 mm
- Edge cross section strip max. 900 mm2
- Edge material roll 0.3 - 3 mm
- Edge cross section max.
- for PVC 135 mm2
- for veneer 100 mm2
- Roll diameter max. 900 mm
- soil conditions must be in accordance with the
  correspond to the foundation plan

JOINING-MILLING UNIT
2 motors each 3 kW, 150 Hz, 9000 1/min
for joint milling of the workpiece edge before the
Glue it on.
Electropneumatic control of the 1 motor.
Work piece blow-off device.
2 DIA joining heads D=125x35x30 mm, KN, Z=2x3
workpiece thickness max. 30 mm
Greater workpiece thicknesses only in conjunction with
DIA cutter head 63 mm high VK-NR. 3492.

NOISE PROTECTION OF THE PART TO BE JOINED

WORKPIECE PREHEATING:
For heating the edge of the workpiece from
Glue specification to improve the gluing quality

GLUING PART A20:
consisting of:
*Hot-melt adhesive unit QA34
Melting unit with granulate container
Electronic temperature control with LED display

*Magazine
for strip material, solid edges and rolls
Feeding of the strip material via vacuum suction cups
Edge monitoring with automatic feed-
stop at missing edge
Magazine height adjustment via spindle
Adjustment range +/- 10 mm

*Roll separator

*Pressure zone C
1 driven pre-compression roller diam. 200 mm
6 pressure rollers diam. 70 mm
Pneumatic pressure adjustment
Central adjustment to different edge-
thick

NOISE PROTECTION UNIT PART BASIC LENGTH:
with central extraction of the chip channel

CAPPING UNIT HL 83 CHAMFER/STRAIGHT
2 motors each 0.5 kW, 200 Hz., 12000 1/min
for cutting off the edge protrusions on front- and
and rear edge
edge thickness chamfer max. 3 mm
2 HM special crosscut saws diam . 120 mm

PNEUMATIC ADJUSTMENT CHAMFER/STRAIGHT
for electro-pneumatic conversion from chamfer to straight.
Manual adjustment of the lateral crosscut fence for
Edge thickness changes required.

PRE-MILLING UNIT 0,55 KW
2 motors one above the other
each 0.55 kW, 200 Hz, 12000 1/min.
Height adjustment with the upper pressure. Working in counter direction.
Swivel range +/- 1 degree.
2 HM cutters 70 x 25 mm, HSK 25, Z = 4
incl. electronic frequency converter with motor brake function
and extension noise protection.
SHAPING MILLING UNIT FK 13
8-FOLD AUTOMATIC. OPTIMAT
for processing the edge protrusions on the workpiece top and bottom
-lower edge and for milling the front and rear edges of the workpiece
rear edge in combination with cross-cut unit and pre-milling unit.
2 motors each 0.55 kW, 200 Hz, 12000 1/min.
automatic 8-fold tool changer
Selector switch for longitudinal/circular milling
Feed rate max. 20 m/min.
workpiece length min. - 240 mm one-sided
                    - 120 mm double sided
Workpiece gap min. 650 mm
workpiece thickness 12 - 60 mm
edge thickness max. 5 mm
Edge overhang top or bottom max. 4 mm
There is a separate tool for each tool type and edge thickness
Replaceable head required
Form milling for veneer and solid edges is only possible
conditionally possible. Incl. frequency converter with motor-
braking function and bicycle suspension Noise protection
Without exchange head and tools

WORKPIECE GUIDE FOR RADIO FREQUENCY UNIT
with additional clamping for workpiece length
min. 120 mm for single sided machines

3 SET OF EXCHANGE HEADS FOR FORM MILLING MACHINES FK
2 processing units for mounting on
Form milling unit FK.

POST-CLEANING UNIT PROFILE
Scanning from above, below and laterally for chamfering
or rounding of pre-milled PVC edges. Blowing nozzles electro-
pneumatically controlled.
edge thickness max. 5 mm
Aggregate can be moved sideways by max. 50 mm at the top and bottom.
Height adjustment with the top pressure.
Without tools. Suction box for PVC chips.

PROFILE KNIFE FOR POST-CLEANING DEVICE
Note: R = 2 mm

REPLASTERING DEVICE GLUE JOINT
Removal of adhesive residues in the area of the glue joint.
Scanning from above and below. Height adjustment with the
Top pressure with carbide knife
Blow nozzles electro-pneumatically controlled.
Unit can be moved sideways by max. 50 mm at the top and bottom.

BUFFING UNIT TOP AND BOTTOM WITH OSCILLATION
to make the edges easy to grip
2 motors each 0,25 kW
inclination and height adjustable
Height adjustment with the top pressure
Oscillation device for exploiting the disc-
width for upper and lower motor
2 molleton discs diam. 150 x 50 x 25 mm

ELECTRONIC HEIGHT ADJUSTMENT
 
peremvastagság: bis 20 mm
munkadarab vastagsága: 12-60 mm
adagolás: 18-24 m/min
vágási egység: yes
ragasztó egység: yes A20
daraboló egység: yes
finom vágási egység: yes
profilvágó egység: yes FK13
sík hántoló egység: yes
profil hántoló egység: yes
élpolírozó egység: yes
vezérlés: NC21
Hozzávetőleges méretek: 9,000 x 1,600 x 2,100 mm
Tömeg kb.: 5,500 kg
Van bármilyen kérdése vonatkozásában a gép? Kérjük, lépjen kapcsolatba velünk.
aukciós jutalék 15%
áfa: plusz áfa
Szállítási feltételek: FCA Rietberg, tehergépkocsira rakodva
Leszerelési és rakodási költségek 450€ (kötelező)
Szállítási költségek: nem tartalmazza
Fizetési feltételek: 100% kifizetés az elhozatalt megelőzően
Dátum: Péntek, 2020.07.31 -ig
Péntek, 2020.07.31, -tól 08:00 -ig 12:00

Hétfő, 2020.07.27 -ig
Csütörtök, 2020.07.30, -tól 08:00 -ig 15:00

Hétfő, 2020.08.03 -ig
Csütörtök, 2020.08.06, -tól 08:00 -ig 15:00

Péntek, 2020.08.07 -ig
Péntek, 2020.08.07, -tól 08:00 -ig 12:00
Surplex App okostelefonhoz
Ingyenes letöltés
iPhone & iPad
Android

Legutóbb megtekintett gépek

Megfigyelt áruk
Elem eltávolítva. Vissza