Surplex használt gépek
Vétel Surplex Trust
Smooth auction process - Surplex informs you about the current situation: more information

Aukció 'KUPER Stock Machines (Part 3)': sorszám 83 REINHARDT VARIO LINE NC 1 Fejező fűrész
Németország, 33397 Rietberg

Lezárási időpont
ekkor: 15 nap 22 óra
2020.07.21, 11:35
Jelenlegi legmagasabb licit
1,850
1 licit, 9 figyeli
Kérem,jelentkezzen be
1,950
következő lehetséges licit
Licitáljon most

Részletek

Árkalkulátor
Nyomtatás
Van bármilyen kérdése vonatkozásában a gép? Kérjük, lépjen kapcsolatba velünk.
Gabriela Angelova (Manager Customer Care)
Gabriela Angelova & a csapat
Név: REINHARDT VARIO LINE NC 1 Fejező fűrész
Termékszám: 564009
Gyártó: REINHARDT
Típus: VARIO LINE NC 1
Gyártás éve: 2002
Ekkortól elérhető: immediately
Gép minősége:
Helyszín: Németország, 33397 Rietberg
- Handheld measuring trolley
- Optimization computer type CONTROL 5.0 Module 5.06
- Conveyor belt type FB 150
- Cross transport RQT 1000 - 8
- High performance crosscut saw type NC 110
- Outfeed conveyor belt FB 150 with length sorting
- Electrical control

Colour: night blue / water blue

Pos. 1: Hand measuring trolley
*********************
in lightweight construction, can be moved by hand. With marking
of workpiece start, end, defects and quality changes
via keystroke. The operation takes place from a sliding
Control panel off.  

* Control panel with defect and quality input via button
* Laser directional light as optical pointer

Pos. 2: Optimization computer type CONTROL 5.0 Module 5.06
*******************************************************
* modular, powerful microprocessor system
* Input terminal with input keyboard and LCD flat screen
* clear and comfortable menu technology, very light
     to handle, no IT knowledge required
* Storage capacity for 300 different lengths,
     divided into 10 cutting lists

Full - optimization according to priority:
------------------------------------------
* Error marking by means of laser directional light

For each cutting list can be the desired priority type,
as well as the permissible waste must be specified separately.
The calculator prefers with:
* priority "length" - the greater length
* Priority "number of pieces" - the higher remaining number
* Priority "valuation code" - the higher
                                          Valuation ratio
* Priority "Smallest waste" - the smaller absolute
                                          Offcuts
* Priority "Number of units and valuation code"  
     - the result from remaining number of units x valuation code

Length sorting:
-----------------
The control of the automatic length sorting is done via
the optimization computer. Each length is calculated by the computer of the corresponding
Drop point assigned. Due to the sorting of the finished lengths
the acceptance of the parts is much easier for the operator.

Automatic balancing of the cutting data:
---------------------------------------------
The automatic balancing of the cutting data takes place according to
the wood throughput in running meters and as a percentage. The
Total quantity, quantity per cutting list, remaining length and the waste
specified.

Furthermore, target, actual and remaining quantity as well as date, time and
the net processing time is displayed for each cutting list.

The machine control is fully automatic: The measuring station
recognizes the total length of the workpiece and the marked
Flaws. This information is processed by the optimization computer
evaluated and passed on to the saw control. The optimal
The desired lengths are divided from the cutting lists
in the light of the priorities set.

The workpieces are cut on the crosscut saw according to the calculated
Cutting program divided up while other workpieces are already
be measured and optimized. Positions, which are processed
(number of pieces reached) are automatically no longer
tailored.

The status of the processing can be called up on the screen at any time
apparent. The balance sheet data can be displayed for a variety of
calculation and control purposes.
(payroll accounting, quality control, purchasing of materials, etc.)

Diagnostic functions
------------------
In the event of a fault, a message appears directly on the screen
with the cause of the malfunction. In addition, the computer
automatically records the last 100 machine states.
Extensive diagnostic functions are available for this purpose.
This data can be called up at any time and traced backwards
will be.

Additional module data transmission with REIAV program
-----------------------------------------------
The control computer is equipped with a data transfer card
which enables data exchange between the system and the office PC.

With the Reinhardt work preparation program you can
easily create cutting orders in the office on the PC or
changed and later transferred to the machine via data transmission
can be loaded. The input is similar to that on the machine.

The balance sheets can also be read out from the machine.

Remote modem diagnosis / remote modem maintenance
------------------------------------
In the event of a fault, the diagnostic information of the machine can be
and evaluated by specialist personnel from Reinhardt
will be. In addition, parameters and machine data can be checked
or be changed or adapted.

There is an analog, shielded telephone connection if possible
with TAE connection socket directly next to or in the switch cabinet of the
machine. The connection must have full authority.
This means that it must be connected directly from outside via a unique telephone number
and you must be reachable from the telephone connection on the machine
can establish a direct connection to the Reinhardt company.

Please note that the telephone line must be routed from power
lines are laid separately.

Pos. 3: Conveyor belt type FB 150
******************************
Belt frame made of solid walls with sliding floor in box construction
edged and welded, belt upper run as sanding belt on
Sheet surface sliding guided, drive and reversing roller
ball bearing mounted, tensioning station on the reversing roller.

Technical data:
transport length 8.000 mm
Belt width 150 mm

incl. 1 storage place for marking the workpieces by the operator

Pos. 4+5: Cross transport RQT 1000 - 8
************************************
As cross conveyor between planer and crosscut saw

consisting of 8 chain strands, base in welded construction,
Chains are guided on the upper side on mounting rails,
Transport chain with straight chain plates, drive-
and deflection stations on ball bearings.

Chains with driving cams, gaps lined
with metal sheets on which the workpieces slide.

Technical data:
centre distance 3.000 mm
transport width 7.000 mm

Pos. 6: Conveyor belt type FB 150
*****************************
Belt frame made of solid walls with sliding floor in box construction
edged and welded, belt upper run as sanding belt on
Sheet surface sliding guided, drive and reversing roller
ball bearing mounted, tensioning station on the reversing roller.

Technical data:
transport length 8.000 mm
Belt width 150 mm

Pos. 7: High performance crosscut saw type NC 110  
        - Working from left to right
**********************************************
for fast, automated processing of trimmed
Workpieces, pneumatically controlled, in stable steel construction.
* electronically positioning feed unit with
     automatic height adjustment with each new workpiece
* PU feed rollers
* Saw blade
* Saw blade feed infinitely variable
* replaceable wear bar in the saw blade area
* Waste disposal directly at the saw blade
* Waste chute locked and secured
* Socket for chip extraction
* complete compressed air preparation unit
* electrical equipment wired for 380 V, 50 Hz,

Cutting areas (see also cutting diagrams):
Cutting height max. 80 mm
Cutting depth max. 200 mm

Technical data:
Saw unit:
Saw blade Z 144 500x30x4 mm
Speed 2,800 rpm
Cutting time per stroke 0.2-3 s
Drive power 5,5 KW
Compressed air requirement 6 bar
Suction socket 1 x * 125 mm
Suction speed 25 m/s

Feed unit:
Electr. controlled three-phase servo drive
Feed speed max. 180 m/min
Acceleration/deceleration 25 m/s2
Drive power 3,5 kW
Positioning accuracy * 1 mm/m
Number of driven rollers 6 pieces
Working height (standard) 900 mm
External dimensions (L x W x H) 1,100 x 1,100 x 1,500 mm

Pos. 8: Outfeed conveyor belt FB 150 with length sorting
******************************************************
with 10 pneumatic ejectors type BFE, on a
stable guide separately guided. The triggering is automatic
via the machine control system.
* Drive and deflection roller mounted in ball bearings
* Tensioning station on the reversing roller
* conveyor belt with guide

Technical data:
transport length 15.000 mm
Belt width 150 mm

Incl. 10 additional contacts for later control
from box 11-20

Item 9: Electrical control of the scope of delivery
***********************************************
Electrical equipment with all necessary switching devices,
ready for mains connection according to VDE 0113 for one operating voltage
from 400 Volt three-phase current and 230 V alternating current - 50 Hz
wired
vágási magasság: 80 mm
vásági mélység: 200 mm
fő motor: 5,5 kW
Hozzávetőleges méretek: 6,000 x 2,500 x 2,500 mm
Tömeg kb.: 4,200 kg
Van bármilyen kérdése vonatkozásában a gép? Kérjük, lépjen kapcsolatba velünk.
Gabriela Angelova (Manager Customer Care)
Gabriela Angelova & a csapat
aukciós jutalék 15%
áfa: plusz áfa
Szállítási feltételek: FCA Rietberg, tehergépkocsira rakodva
Leszerelési és rakodási költségek 450€ (kötelező)
Szállítási költségek: nem tartalmazza
Fizetési feltételek: 100% kifizetés az elhozatalt megelőzően
Dátum: Péntek, 2020.07.31 -ig
Péntek, 2020.07.31, -tól 08:00 -ig 12:00

Hétfő, 2020.07.27 -ig
Csütörtök, 2020.07.30, -tól 08:00 -ig 15:00

Hétfő, 2020.08.03 -ig
Csütörtök, 2020.08.06, -tól 08:00 -ig 15:00

Péntek, 2020.08.07 -ig
Péntek, 2020.08.07, -tól 08:00 -ig 12:00
Surplex App okostelefonhoz
Ingyenes letöltés
iPhone & iPad
Android

Legutóbb megtekintett gépek

Megfigyelt áruk
Elem eltávolítva. Vissza