적절한 기계-제안 IDM Idimatic/66 엣진 밴딩기

엣진 밴딩기 HOMAG Optimat KL 77/A20/S2
0 Gebote
6,500 €
12-15-2016
10:00
HOLZHER SPRINT 1411 K Edge Banding Machine
59 Gebote
7,000 €
12-06-2016
09:27
OTT Altantic Edge Banding Machine
0 Gebote
5,500 €
12-15-2016
12:23
엣진 밴딩기 BRANDT KD 68
10 Gebote
900 €
12-15-2016
10:22
Surplex - 입찰하기 매우 쉽습니다!
등록하기
경매를 선택하세요
입찰하세요
더 자세히 알아보세요
귀하의 성공적인 판매를 위한 3가지 방법들!
구매
경매
마켓팅
더 자세히 알아보세요

IDM Idimatic/66 엣진 밴딩기

품목이 고객님의 관찰목록
IDM Idimatic/66 엣진 밴딩기
IDM IDIMATIC/66 엣진 밴딩기
판매됨
   

죄송합니다, 이 기계는 이미 판매완료되었습니다

구매가능한 유사 기계들을 찾아 보세요

비용 및 혜택

경매 수수료   15%
부가가치세   * 부가가치세 추가
배송 조건   트럭 적재
해체 및 적재 비용   400.00 € (확정)
운송 비용들   포함되지 않음
결제 조건   수령전 100% 결제

기계 상세정보

이름   IDM Idimatic/66 엣진 밴딩기
기계 번호   185033
제조업체   IDM
모델/타입   Idimatic/66
제조 년도   1995
기계 구매가능 시기   11.17.2014
기계 품질   정상작동 상태
기계 위치   33070 BUDOIA (PN), Italien

기술적인 세부사항

엣지 두께   0,4 - 5 mm
가공물 두께   10 - 50 mm
가공물 너비 최소   140 mm
조인트 트리밍 장치   2 x 2,2 kW
절단 장치   2 x 0,35 kW
대략 규격   7500 x 1400 x 2400 mm
대략 중량   3800 kg

설명

•Edgebanding thickness capacity, 10 – 50 mm panel thickness, 60 mm minimum panel width & 140 mm minimum length

•Pre-milling station with (2) 3 HP – 12,000 RPM counter rotating vertical milling heads: both with pneumatic jump control, 30 mm spindles, fully enclosed by noise insulated cabin

•Gluing unit for edges up to 3 mm thickness, 56 mm height.

•Front & rear end trims (motors 0.5 HP – 12,000 RPM each), motors tilt 0° - 15° on horizontal plane, 45° chamfer cut with on/off on control.

•Top & bottom rough trims (motors 0,7 HP – 12,000 RPM each), (prepared for “quick change” of motors, for interchangeable 2nd set of bevel/radius trim units)

•Top & bottom fine/bevel/profile multi-function trims (motors 0.6 HP – 12,000 RPM each), tilts 0°- 10° for bevel and 3 mm PVC corner round (prepared for “quick change” of motors, for interchangeable 2nd set of bevel/radius trim units)

•Moulding unit (motor 2,5 HP – 12,000 RPM each), units tilt 0° - 90°.

•Corner rounding units from trimming leading & trailing upper and lower edge/corners when edgebanding all (4) sides or when edgebanding “soft- or postformed” panels (4 motors 0.7 HP – 12,000 RPM each).

•Top & bottom scrapers for up to 5MM thick PVC banding, pneumatic pressure control for scraping knives, digital readouts, overhead PVC filter unit eliminates PVC chips being sucked in by dust collector.

•Top & bottom PVC edge color & surface reactivation unit, LEISTER hot air blower with temperature adjustment

•Function & line control with microprocessor

•Microprocessor displays stored data, on/off workstation sequence & trouble shooting diagnostic; data input by alphanumeric keyboard; microprocessor adjusts according to stored programs or input; top pressure beam opening, pressure section position & pressure control, in/out pneumatic sideways positioning of “trim/scrap/corner round” workstations, on/off sequence of workstation motors

•Equipped with automatic strip & coil feed magazine with 3 mm PVC guillotine

•0.7 Kg capacity overhead granular glue “Quick Melt” hopper feeding compact size, Teflon coated lower applicator glue pot, 25 mm diameter glue applicator roller, reversible rotation by flip of switch

•Pressure section with (1) large diameter (200 mm) clutch controlled drive roller and (4) jump action, pneumatic pressure idle rollers, horizontal Adjustment w/digital indicator

•Hardened steel link feed chain with “anti-slip” 80 mm wide rubber pads

•(2) feed speeds, with 2.2 Kw or 3.3 Kw drive

•Motorized adjustment of top pressure beam. Heated infeed fence, automatic panel spacing control, remote control job button, insulated sound enclosure over all trim stations; rotating operator control panel at eye-level height, 15 KVA – 240 Hz frequency inverter & complete set of used tooling

Machine specifications are based on original manufacturer’s information as reported in the original manual of this machine and are subject to verification.
위로 가기