ustrezni predlogi strojev IDM Idimatic/66 Lepilka

HOMAG Optimat KL 77/A20/S2 Robna lepilka
0 Gebote
6,500 €
15.12.2016
10:00
HOLZHER SPRINT 1411 K Edge Banding Machine
59 Gebote
7,000 €
06.12.2016
09:27
OTT Altantic Edge Banding Machine
0 Gebote
5,500 €
15.12.2016
12:23
BRANDT KD 68 Robna lepilka
10 Gebote
900 €
15.12.2016
10:22
Surplex - tako enostavno je sodelovati na dražbi!
Registrirajte se
Izberite dražbo
Ponudba
Izvedite več
Trije načini za uspešno prodajo!
Kupi
Dražba
Marketing
Izvedite več

IDM Idimatic/66 Lepilka

Ta izdelek je na vašem Opazovalni seznam

Oprostite, ta stroj je že bil prodan

Odkrijte podobne stroje, ki so na voljo

Cena in ugodnosti

provizija dražbe   15%
DDV   *plus DDV
Pogoji dostave   naloženo na dostavno vozilo
Cena demontiranja in nalaganja   400.00 € (binding)
Cena prevoza   ne vsebuje
Pogoji plačila   100% plačilo pred prevzemom

Podrobnosti stroja

Ime   IDM Idimatic/66 Lepilka
Številka stroja   185033
Proizvajalec   IDM
Model / Vrsta   Idimatic/66
Leto izdelave   1995
Stroj na voljo od   11.17.2014
Kakovost stroja   delujoče
Lokacija stroja   33070 BUDOIA (PN), Italien

Tehnične podrobnosti

debelina roba   0,4 - 5 mm
debelina obdelovanca   10 - 50 mm
min. širina obdelovanca   140 mm
skupna enota za obrezovanje   2 x 2,2 kW
enota za rezanje   2 x 0,35 kW
Približne mere   7500 x 1400 x 2400 mm
Približna teža   3800 kg

Opis

•Edgebanding thickness capacity, 10 – 50 mm panel thickness, 60 mm minimum panel width & 140 mm minimum length

•Pre-milling station with (2) 3 HP – 12,000 RPM counter rotating vertical milling heads: both with pneumatic jump control, 30 mm spindles, fully enclosed by noise insulated cabin

•Gluing unit for edges up to 3 mm thickness, 56 mm height.

•Front & rear end trims (motors 0.5 HP – 12,000 RPM each), motors tilt 0° - 15° on horizontal plane, 45° chamfer cut with on/off on control.

•Top & bottom rough trims (motors 0,7 HP – 12,000 RPM each), (prepared for “quick change” of motors, for interchangeable 2nd set of bevel/radius trim units)

•Top & bottom fine/bevel/profile multi-function trims (motors 0.6 HP – 12,000 RPM each), tilts 0°- 10° for bevel and 3 mm PVC corner round (prepared for “quick change” of motors, for interchangeable 2nd set of bevel/radius trim units)

•Moulding unit (motor 2,5 HP – 12,000 RPM each), units tilt 0° - 90°.

•Corner rounding units from trimming leading & trailing upper and lower edge/corners when edgebanding all (4) sides or when edgebanding “soft- or postformed” panels (4 motors 0.7 HP – 12,000 RPM each).

•Top & bottom scrapers for up to 5MM thick PVC banding, pneumatic pressure control for scraping knives, digital readouts, overhead PVC filter unit eliminates PVC chips being sucked in by dust collector.

•Top & bottom PVC edge color & surface reactivation unit, LEISTER hot air blower with temperature adjustment

•Function & line control with microprocessor

•Microprocessor displays stored data, on/off workstation sequence & trouble shooting diagnostic; data input by alphanumeric keyboard; microprocessor adjusts according to stored programs or input; top pressure beam opening, pressure section position & pressure control, in/out pneumatic sideways positioning of “trim/scrap/corner round” workstations, on/off sequence of workstation motors

•Equipped with automatic strip & coil feed magazine with 3 mm PVC guillotine

•0.7 Kg capacity overhead granular glue “Quick Melt” hopper feeding compact size, Teflon coated lower applicator glue pot, 25 mm diameter glue applicator roller, reversible rotation by flip of switch

•Pressure section with (1) large diameter (200 mm) clutch controlled drive roller and (4) jump action, pneumatic pressure idle rollers, horizontal Adjustment w/digital indicator

•Hardened steel link feed chain with “anti-slip” 80 mm wide rubber pads

•(2) feed speeds, with 2.2 Kw or 3.3 Kw drive

•Motorized adjustment of top pressure beam. Heated infeed fence, automatic panel spacing control, remote control job button, insulated sound enclosure over all trim stations; rotating operator control panel at eye-level height, 15 KVA – 240 Hz frequency inverter & complete set of used tooling

Machine specifications are based on original manufacturer’s information as reported in the original manual of this machine and are subject to verification.
Pojdi na vrh