1 / 51
2009 Avermann AVOS 1410-45-85Baling press 80 t refurbished and tested
- Current bid
- Status
Lot specifications
- Quantity
- 1
- Margin
- No
- Brand
- Avermann Maschinenfabrik GmbH & Co. KG
- Type
- AVOS 1410-45-85
- Year of build
- 2009
- Serial number
- 60344S
- Bale press model
- Yes
- Waste compactor model
- Yes
- Foil / carton press model
- Yes
- Horizontal
- Yes
- Machine weight
- 16000kg
- Terms of delivery
- Ex foundation-unpackaged
Description
Technical data baler:
Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany
Type AVOS 1410-45/80
Year of construction 2009
Operation hours 22,029 hours, as of December 2025
Press power main press 80kN
Specific press force 103,9 N/cm²
Feed channel 1,400 x 1,000 mm
Theoretic cycle time 12 sec
Theoretic throughput capacity 300 m³/h
Bale size 1,100 x 750 (w x h), the length is variable
Drive power 45 kW
Connected load 75 kW
Tying system 4-fold, vertical, fully automatic
Throughput capacity at a
bulk weight of 30 kg/cbm approx. 6.0 t/h
bulk weight of 50 kg/cbm approx. 10.5 t/h
bulk weight of 100 kg/cbm approx. 17,5 t/h
Bale weight with a bale length of approx. 1.2 m up to 600 kg, depends on material
SPS controller Siemens S7-300
Operating panel pulsotronic
Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h)
Transport weight baler approx. 16 t
Special equipment:
Wear-resistant floor
Special press ram for pressing 'difficult' materials and loose bulk materials with small grain sizes
Control cabinet air conditioning
Machine foot elevation 200 mm
refurbished and tested December 2025
Remarks
The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced:
• Dismantling of the press ram, disassembly into individual parts, reconditioning of the mechanics, replacement of the following plastic wear plates and rails:
o Plastic wear rails left/right under the press ram
o Plastic wear rails left/right above the press ram
o Plastic main wear plate (support plate) in the centre under the press ram
• Steel guide rails on the left/right in the frame
• Replacement of the entire base plate, four-piece, made of wear-resistant steel
• Wire inlet rails in the press floor newly welded and smoothed
• Replacement of the counter blade, two-piece, in the frame
• Adjustment of the blade gap
• Dismantling of the binding and twisting unit, disassembly into individual parts, loosening of the mechanics, replacement of all deep groove ball bearings and axial ball bearings on the twisting shafts, wire blades cleaned and readjusted, chains greased and tensioned
• Support roller in front of the twisting shafts replaced
• Hydraulic hoses replaced
• Oil filter and air filter replaced
• Main hydraulic cylinder checked for leaks
• The hydraulic oil is only one year old, has been chemically analyzed, is still in good condition, and has therefore not been changed but can continue to be used.
• General maintenance work carried out
Finally, the machine tested during operation, without the use of materials, in manual mode and in automatic mode.
Additional details
The collection of the purchased goods is done as follows:
After receiving your payment, the seller will contact you to make a pick-up appointment. You will then receive the exact address.
The city and province where the plots are located is indicated with the plot.
The minimum age for visiting the collection days is 18 years. Visitors must be able to identify themselves.
There is no right of withdrawal. See the Auction Terms and Conditions for more information.
No viewing day will be organized for this auction.
For each lot, an administration fee of € 100 will be charged.
