Použité stroje Surplex
Prodej Surplex Trust
Smooth auction process - Surplex informs you about the current situation: more information

Aukce 'KUPER Stock Machines': č. série 56 HOMAG KL 79/01/A20/S2 Olepovačka hran
Německo, 33397 Rietberg

Ukončení aukce
24.03.2020, 10:52
Aukce byla ukončena
8,300
Prohlédněte si podobné dostupné stroje
Přejít na seznam

Podrobnosti

Tisk
Máte nějaké otázky týkající se stroji? Prosím kontaktujte nás.
Název: HOMAG KL 79/01/A20/S2 Olepovačka hran
Č. stroje: 563351
Výrobce: HOMAG
Model / typ: KL 79/01/A20/S2
Rok výroby: 1999
Stroj je k dispozici od: immediately
Stav stroje:
Lokalita: Německo, 33397 Rietberg
HOMAG - F U E G E - K A N T E N - OPTIMAL

One-sided machine for joint milling of straight
workpiece edges, gluing and finishing
of different edge materials from the
Roll or strip, up to 20 mm edge thickness,
in longitudinal and transverse throughput.

Fixed stop side on the left.

BASIC MACHINE:
--------------
- with continuous machine stand for
  flexible structure of the processing units
- Workpiece support with roller rail,
  telescopic approx. 800 mm
  1800 mm, 2nd roller conveyor fixed on the
  Floor mounted.
- Chip channel in machine base
- Glue roller drive with feed stop
- Glue container lift-off at feed stop
- Glue container clamping workpiece-actuated
- Adjustable infeed ruler

WORKPIECE TRANSPORT DEVICE:
------------------------------
- transport chain 80 mm wide with rubber pad
- hardened precision running and guide surfaces
- magnetic braking of the transport chain

SURFACE:
----------
- with driven compound V-belt
- motor-driven height adjustable with digital
  Position display

PAINTING:
-----------
- HOMAG textured paint grey RDS 240 80 05

ELECTRICAL EQUIPMENT:
-----------------------
- Operating voltage 380/400 Volt, 50/60 Hz.
- Country specific operating voltage adjustment
  via transformer (optional at extra cost)
- Control voltage 24 Volt
- Switch cabinet mounted, according to Euronorm
  EN 60204 installed
- electronic frequency converters with
  Motor brake function
- Manual switch for setup mode

HOMATIC ELECTRONIC CONTROL:
----------------------------
- Programmable logic controller (SPS)
  with LED display of all in- and
  Outputs
- Integrated draw frame control for contact
  Loose control of the processing aggregates
- Prescribed ambient temperature:
  + 5 degrees to + 35 degrees Cels.
- expandable with network connection EtherNet

INPUT NC21
------------
with graphical user interface for easy and
comfortable operation and programming of a
HOMAG machine.
Hardware:
- Industrial computer 68040 with 16 MByte RAM
- 1 PCMCIA hard disk 170 MByte
- 1 free PCMCIA slot for data backup
- Colour display 12.1" with PC-compatible keyboard
installed in the control panel at the inlet

software:
- Real-time operating system OS9 with window interface
- Operation with Windows standard via selection menu
- menu-driven creation of work programs
- Production according to work programmes
- SPS diagnosis in ladder diagram technology on the display

Remote diagnostics:
- Telephone modem (analog) against sparater

Calculation
- On site, two telephone lines up to the
  machine to be installed, one with speech apparatus

SAFETY AND PROTECTIVE EQUIPMENT:
-------------------------------------
- all machines for EU member states with
  CE mark according to EC Machinery Directive
  89/392/EEC Annex IIA
- Wood dust tested TRK value max. 2 mg/m3 at
  Compliance with the requirements to be provided by the customer
  Extraction capacity according to extraction plan
- Documentation

TECHNICAL DATA:
-----------------
- feed infinitely variable 18 - 24 m/min.
- working height 950 mm
- Working width minimum:
                - 55 mm with workpiece thickness 22 mm
               - 100 mm for workpiece thickness 60 mm
(depending on the workpiece length)
- workpiece overhang 30 mm
- workpiece thickness 12 - 60 mm
- Edge material strips max. 0.4 - 20 mm
- Edge cross section strip max. 900 mm2
- Edge material roll 0.3 - 3 mm
- Edge cross section max. - for PVC 135 mm2
                         - for veneer 100 mm2
- Roll diameter max. 900 mm
- Ground conditions must correspond to the foundation plan
  correspond to

LATE CONVEYOR BELT
installed in the machine stand.
Central suction socket at the machine outlet.
Cannot be retrofitted on KF/KL 25/26

PRE-INSTALLATION FOR EXTENSION BOOMERANG/TFU
Feed interlock and mechanical
Interface adaptation
for Ligmatech Boomerang

AUTOMATIC ADJUSTMENT INFEED RULER
for optimals with a prefixed joining part

JOINING-MILLING UNIT
----------------
2 motors each 3 kW, 150 Hz., 9000 1/min
for joint milling of the workpiece edge before the
Glue it on.
Electropneumatic control of the 1 motor.
Work piece blow-off device.
2 DIA joining heads D=125x35x30 mm, KN, Z=2x3.
Workpiece thickness max. 30 mm.
Larger workpiece thicknesses only in connection with
DIA cutter head 63 mm high VK No. 3492.

CONTROL MOTOR 2, JOINING-MILLING
electropneumatic control of the 2nd motor

NOISE PROTECTION JOINING PART
-------------------

WORKPIECE PREHEATING
-------------------
for heating the workpiece edge before the
Glue specification to improve the gluing quality

GLUED PART A20
---------------
consisting of:

Hot-melt adhesive unit QA34
Melting unit with granulate container
Electronic temperature control with LED display

Magazine
for solid edges, strips and rolls
Feeding of the strip material via vacuum suction cups
Edge monitoring with automatic feed-
stop at missing edge
Magazine height adjustment via spindle
Adjustment range +/- 10 mm.

Roll separation device

Pressure zone C
1 driven pre-compression roller diam. 150 mm
6 pressure rollers diam. 70 mm
Pneumatic pressure adjustment
Central adjustment to different edge-
thick

HARDO FEED MELTING UNIT FOR PU-BONDING
----------------------------------------------

FEEDING DEVICE 2 ROLLERS  
with inclined driven rollers
and intermediate transport at the infeed 350 mm long.
Min. workpiece length 250 mm

EXTENSION OF MAGAZINE A/E12/A20 TO 6 ROLLS
instead of single roller
Edge thickness 2 x 3 mm and 4 x 1 mm.
Roll diameter 2 x 900 mm and 4 x 600 mm.
Automatic or manual roll change.
Residual length monitoring at 2400 mm.

GLUE ROLL DRIVE HOT MELT GLUE
Controlled depending on temperature, thus the
Glue roll continues when the feed is switched off.

AUTOMATIC ADJUSTMENT PRESSURE ZONE
for automatic adjustment of the pressure zone in case of
different edge thicknesses.

NOISE PROTECTION UNIT PART BASIC LENGTH
----------------------------------

HEAD UNIT HL83 CHAMFER/STRAIGHT
-----------------------------
2 motors each 0.5 kW, 200 Hz., 12000 1/min
for cutting off the edge protrusions on front- and
and rear edge
edge thickness chamfer max. 3 mm
2 HM special crosscut saws diam. 120 mm
Caps are not possible if the surface layer protrudes.

PNEUMATIC ADJUSTMENT LATERAL CROSSCUT MOTOR
for electropneumatic lateral adjustment
of the cross-cut motors to 2 positions.
Position 1 - flush caps
Position 2 - Caps with overhang - for repositioning
Milling with form milling unit

PNEUMATIC ADJUSTMENT CHAMFER/STRAIGHT  
for electro-pneumatic conversion from chamfer to
Even. Manual adjustment of the lateral
Cross-cut stop for edge thickness changes
required.

PRE-MILLING UNIT 1,5 KW  
2 motors one above the other
each 1.5 kW, 200 Hz., 12000 rpm.
Height adjustment with the upper pressure. In the counter direction
working. Swivel range +/- 1 degree.
2 HM milling cutters 70 x 25 mm, HSK 25, Z=4
Including electronic frequency converter with
Engine brake function and extension noise protection.

PNEUMATIC ADJUSTMENT PRE-MILLING UNIT
to 2 positions
Position 1 - Pre-milling with edge overhang (approx. 0.2 mm)
Position 2 - Flush milling without edge overhang

NOTE:
--------
1. manual adjustment for edge overhang at the top 5 mm.
2. four-sided processing with edge overhang
   top with workpiece inlay.

FORM MILLING UNIT FK 13, 8-FOLD AUTOMATIC
for machining the edge protrusions on the
upper and lower edge of the workpiece and for
Milling of the front and rear edge of the workpiece
in connection with cross-cutting unit and pre-milling unit.
2 motors each 0.4 kW, 200 Hz, 12000 1/min.
Automatic 8-fold tool changer.
Selector switch longitudinal/circular milling.
Feed rate max. 20 m/min.
workpiece length min. - 240 mm one-sided
                    - 120 mm double sided
Workpiece gap min. 650 mm
workpiece thickness 12 - 60 mm
edge thickness max. 5 mm
Per tool type and edge thickness is one
separate exchange head required.
Form milling for veneer and solid edges is
is only possible to a limited extent.
Flush/bevel milling of glued softforming edges
is not possible.
Incl. frequency converter with motor brake function
and extension noise protection.

NOTE:
--------
incl. 1 interchangeable head set; chamfer

CHANGE HEAD FOR FORM MILLING FK
2 processing units for mounting on
Form milling unit FK. Without tools.

MANUAL ADJUSTMENT FOR FK-UNIT
for manual adjustment with same radii
at different edge thicknesses
e.g. R=3 mm at edge thickness 3 mm or 6 mm
and to move away from the work area manually.
The milling of the same radii on different
Edge thickness is only possible during longitudinal processing
possible. The device scanning
is then carried out on the edge material.

WORKPIECE GUIDE FOR RF EQUIPMENT
with additional clamping for workpiece length
min. 120 mm for single sided machines.

2 X UNIVERSAL MILLING AGGREGATE 4 KW, CONTROLLED
Milling stands, cross support with spindle adjustment
1 motor 4 kW, 150 Hz., 9000 rpm
at the back of the stand, swivelling max. 90 degrees
Incl. intermediate support electropneumatic
controlled, suction hood on top, reversing switch
for direction of rotation. For tool diameter
max. 150 mm. Without tools.
Incl. electronic frequency converter with
Engine brake function and extension noise protection.

AUTOMATIC MULTI-CLEANING DEVICE
for max. 3 different profiles.
Scanning from above, below and sideways to
Chamfering or rounding of pre-milled PVC edges.
Blowing nozzles electro-pneumatically controlled.
For the automatic retooling of chamfers/radii and
electropneumatic lateral retraction from
the work area for upper and lower tool.
Height adjustment with the upper pressure.
edge thickness max. 3 mm
workpiece thickness min. 13 mm with R=3 mm
min. 10 mm with chamfer 0,5x45 degrees
Incl. suction box for PVC shavings,
2 HM knives designed for bevel 20 degrees,R=2/R=3.

REPLASTERING DEVICE GLUE JOINT
Removal of adhesive residues in the area of the
Glue line. Scanning from above and below.
Height adjustment with the upper pressure
with carbide knife
Blowing nozzles electro-pneumatically controlled
Aggregate top and bottom max. 50 mm laterally
moveable.
2 X PNEUMATIC APPLICATION CONTROL
For glue joint scraper blade.

BELT SANDING UNIT KS 10  
for grinding straight edges
Sanding belt speed 10 m/sec.
belt length = 2100 mm
belt width = 120 mm
grinding pressure manually adjustable
Belt radiation via nozzle
Oscillation device
POWER : 1,5 KW

PNEUMATIC ADJUSTMENT KS 10
for electro-pneumatic lateral movement
on manual 8-fold turret for different
Edge thicknesses

CHAMFER/RADIUS GRINDING UNIT BOTTOM PS41
1 motor 0,55 kW
workpiece thickness min. 12 mm
Radius max. 12 mm
Sanding belt length 2000 mm. Belt width 20-35 mm.
Belt speed 7 m/sec.
Sanding pressure manually adjustable.
1 chamfering sanding shoe

PNEUMATIC ADJUSTMENT PS41
for electropneumatic lateral retraction
from the work area

CHAMFERING/RADIUS GRINDING UNIT TOP PS42
1 motor 0,55 kW
Height adjustment with the upper pressure.
workpiece thickness 12 - 60 mm
Radius max. 12 mm
Sanding belt length 2000 mm. Belt width 20-35 mm.
Belt speed 7 m/sec.
Sanding pressure manually adjustable.
1 chamfering sanding shoe

PNEUMATIC ADJUSTMENT PS42
for electropneumatic lateral retraction
from the work area

BUFFING UNIT TOP AND BOTTOM WITH OSCILLATION
to make the edges easy to grip
2 motors each 0,25 kW
Height and inclination adjustable
Height adjustment with the top pressure
Oscillation device for exploiting the
Disc width for upper and lower motor
for molleton discs diam. 150 x 50 x 25 mm
 
Přibližné rozměry: 20,000 x 2,500 x 2,400 mm
Přibližná hmotnost: 8,500 kg
Máte nějaké otázky týkající se stroji? Prosím kontaktujte nás.
Aukční poplatek 15%
DPH: *plus DPH
Dodací podmínky: FCA Rietberg, naloženo na kamion
Náklady na demontáž a nakládku 450€ (binding)
Náklady na dopravu: neobsahuje
Platební podmínky: Platba v plné výši před odběrem
Datum: Pondělí, 20.04.2020 do
Pátek, 24.04.2020, od 08:00 do 15:00
Surplex App - nyní také pro Android!
Zdarma ke stažení:
iPhone & iPad
Android

Naposledy zobrazené stroje

Seznamu sledovaných
Položka byla odstraněna. Vrátit